Introduction to Roots blower in electroplating factory, Three leaf Roots blower specifications, model parameters

Roots blower in electroplating factoryis a device that generates positive pressure or negative pressure through the relative rotation of two impellers, thus compressing and conveying gas.。The following is to introduce the Roots blower in electroplating factory:

1、Brief introduction of Roots blower in electroplating factory

Roots blower in electroplating factorya rotary compressor that uses two lobed rotors to move relative to each other in a cylinder to compress and transport gas.，it can be used in pottery and porcelain, aquaculture, Food and beverage processing, coal chemical industry, Dust removal and other industries。

Roots blower in electroplating factory

2、Roots blower in electroplating factory structure

The Roots blower in electroplating factory structure is introduced as follows:

1. case

It mainly plays the role of supporting (wallboard, impeller, muffler) and fixing. The casing is the external structure of the Roots blower in electroplating factory, which is used to support and fix the rotor, bearings and other components, while ensuring the gas tightness.

2. bearing

It is used to support the rotation of the rotor and bear the weight of the rotor and the load during operation.

3. wallboard

It is mainly used to connect the casing with the impeller, support the rotation of the impeller, and play the role of end sealing.

4. impeller

It is the rotating part of the Roots blower in electroplating factory, which is divided into two leaves and three leaves. However, due to many advantages such as smaller air pulsation, less noise and smoother operation, the three-leaf Roots blower in electroplating factory has gradually replaced the two-leaf Roots blower in electroplating factory.

5. fuel tank

Mainly used for storing lubricating oil used for lubricating gears and bearings. The oil tank is used to store lubricating oil to lubricate bearings and gears and reduce wear and friction.

Roots blower in electroplating factory

3、Functional advantages of Roots blower in electroplating factory

Roots blower in electroplating factorys have the following advantages.

1. Long service life

The mechanical friction of the Roots blower in electroplating factory is small and the loss is low, so its service life is relatively long. This enables it to maintain high working efficiency and stability in long-term operation.

2. Convenient maintenance

The structure of the Roots blower in electroplating factory is relatively simple and easy to maintain.

3. energy-efficient

The Roots blower in electroplating factory has high efficiency and can realize gas transportation and pressurization with low energy consumption.

4. Long service life

The mechanical friction of the Roots blower in electroplating factory is small and the loss is low, so its service life is relatively long. This enables it to maintain high working efficiency and stability in long-term operation.

5. Stable and reliable

The Roots blower in electroplating factory has simple structural design, stable and reliable operation and convenient maintenance. This enables it to maintain high working efficiency and stability in long-term operation.

Roots blower in electroplating factory

4、Roots blower in electroplating factory video live broadcast

On-site aerial photography of Roots blower in electroplating factory。

Roots blower in electroplating factory

As you can see from the live video.，hyde powder the principle is simple.When the motor drives one impeller to rotate, the other impeller will rotate synchronously at the same speed and in the opposite direction under the action of the synchronous gear. In the process of rotation, because the gaps between impeller and impeller, impeller and casing, impeller and wallboard are very small, a vacuum state is formed at the air inlet, and air is sucked into the air inlet cavity under the action of atmospheric pressure. As the impeller continues to rotate, two blades of each impeller, the wallboard and the casing form a sealed cavity, and the air in the air inlet cavity is continuously brought to the exhaust cavity by the sealed cavity formed by the two blades. Because the impellers in the exhaust cavity are meshed with each other, the air between the two blades is squeezed out. After continuous inhalation and extrusion, air is continuously transported from the air inlet to the air outlet, completing the whole gas transportation process.。

5、Advantages of Roots blower in electroplating factory principle

Roots blower in electroplating factoryat work,It mainly depends on the relative movement of two lobed rotors (usually three-bladed impellers) in the cylinder to compress and transport gas.，is a Roots blower in electroplating factory，be loved by our customers.。

Roots blower in electroplating factory

6、Roots blower in electroplating factory characteristics

Roots blower in electroplating factoryfeatures include smooth operation, strong adaptability, wide application range, run smoothly and low noise，the advantage is Small size and small floor space make it easy to arrange and install in places with limited space.、The structural form of the three-blade rotor and the reasonable structure of the air inlet and outlet in the shell make the fan have small vibration and low noise.、Due to the adoption of synchronous gear transmission and small gap design, the Roots blower in electroplating factory runs stably and reliably, without contact and wear parts, and has a long service life.、Because of the design of three-blade rotor, the Roots blower in electroplating factory has little vibration and low noise during operation, and the operation is stable and reliable、In the process of air intake and exhaust, the Roots blower in electroplating factory will not produce air pulsation, which means that it does not need an additional buffer gas tank to output gas smoothly. This is particularly important for processes that require stable airflow.，is a positive displacement blower with forced gas transmission characteristics.，it has the functions of supply air, sewage disposal, aquaculture, dehydrate and ventilation，is based on hyde powder is an advanced Roots blower in electroplating factory developed by our company in combination with the actual situation of the industry。

Roots blower in electroplating factory

Roots blower in electroplating factoryis a positive displacement blower.，the main structure includes case, rotator, muffler, wallboard, bearing and so on，Roots blower in electroplating factoryThe overall structural design is simple, diverse and beautiful.，is a kind of high quality and low price Roots blower in electroplating factory。